- +91 9024156475
- info@zinbal.com


Sensors
View AllLM393-based design.
Sensitivity adjustable (potentiometer adjustment).
Operating voltage: 3.3V to 5V DC.
Operating current: 15mA.
Module pin 3 pins.
The output type is digital output (D0).
Operate on Low Power
Connection Interface: I2C
operating voltage 2.5 ~ 3.6 V
12 sensing inputs
Auto calibration of each sensor
Operating Voltage: 2.5V-5.5V
Startup Calibration Delay: 0.5 Sec
Current Consumption: < 7 µA
Simple, easy to use, with Auto Calibration
Input voltage: 4 V to 12 V (+ 5 V recommended)
Output: Digital Signal
Working range: up to 20 cm away
Able to work at low current (20mA)
Operating Voltage: 5 Volt
Preheat Duration:20 s
Output: Both digital and analog
The Sensitivity of Digital pin can be varied using the potentiometer
Operating Voltage: 5 Volt
Preheat Duration:20 s
Output: Both digital and analog
The Sensitivity of Digital pin can be varied using the potentiometer
Motors & Drivers
View AllWheel Diameter – 70 mm
Wheel Width – 20 mm
Shaft Diameter – 6 mm
Weight: 33gm
Modulation: Analog
Torque:
- 4.8V: 2.20 kg-cm
- 6.0V: 2.50 kg-cm
Speed: 4.8V: 0.11 sec/60°, 6.0V: 0.10 sec/60°
Weight: 0.49 oz (14.0 g)
Gear Type: Metal
Rotation/Support: Dual Bearings
Rotational Range: 180°
Pulse Cycle: 20 ms
Pulse Width: 400-2400 µs
Model: SG90
Weight: 9 gm
Operating voltage: 3.0V~ 7.2V
Servo Plug: JR
Stall torque @4.8V : 1.2kg-cm
Wheel Size: 65mm x 26mm
WEIGHT: 20.00g
The geared DC motor will operate on voltages between 3-9VDC.
Plastic Yellow Rim
Robot Wheel is suitable for all BO motors
Programmable Boards
View AllMicrocontroller: ATmega328P
Digital I/O Pins: 14, with 6 PWM outputs
Analog Input Pins: 8
Operating Voltage: 5V
Clock Speed: 16MHz
USB Connection
Power Jack
Reset Button
Microcontroller: ATmega2560
Operating Voltage: 5V
Input Voltage : 7-12V
Digital I/O Pins: 54 (of which 15 provide PWM output)
Analog Input Pins: 16
DC Current per I/O Pin: 20 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 256 KB
SRAM: 8 KB
EEPROM: 4 KB
Clock Speed: 16 MHz
Drive Type: Dual high-power H-bridge
Power Input: 4.5 to 9V
Communication Interface Voltage: 3.3V
Flash size: 4MB
Operating Temperature: -40 to 125°C
Transfer Rate: 110 to 460800Kbps
AD0: 1 channel ADC
Microcontroller: ATmega328P
Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Digital I/O Pins: 14, of which 6 can be used as PWM outputs
Analog Input Pins: 61
DC Current per I/O Pin: 20mA
DC Current for 3.3V Pin: 50mA
Flash Memory: 32KB (ATmega328P), 0.5KB used by bootloader
SRAM: 2KB (ATmega328P)
EEPROM: 1KB (ATmega328P)
Clock Speed: 16 MHz
Reset Button
Wireless Modules
View AllInput Supply Voltage: 2.5 ~ 5.5(VDC)
Transmission Distance: 45 m
Carrier Frequency: 38 kHz
Beam Angle: 45 deg
Viewing Angle: 45 deg
Output Current: 5 mA
Power Dissipation: 10 mW
Receiver Type 50 Channels
GPS L1 frequency, C/A Code
SBAS: WAAS, EGNOS, MSAS
Input Supply Voltage: 2.7 ~ 6 VDC
Main Chip: NEO-6
Navigation Update Rate 5Hz
Position Accuracy: 2Meter
Operating Temperature Range: -24 to 84 °C
Tracking Sensitivity: -161 dBm
Avg Cold Start Time: 27s
Warm Start Time: 27s
Maximum Speed: 500 M/s
The HC-05 6 Pin Wireless Serial Bluetooth Module is a Bluetooth module to be used with any microcontroller. It uses the UART protocol to simplify sending and receiving wireless data.
Operating voltage: 3.6 ~ 6V.
Input current: 50mA
Maximum Operating Range: 10m.
Operating Frequency: 2.4GHz ISM band.
Modulation: GFSK (Gaussian Frequency Shift Keying).
Operating Temperature: -20 ~ +75℃.
Operating voltage: 5V.
Quiescent Current: 4mA.
Receiving frequency: 315MHz.
Receiver sensitivity: 105 dB.
Communication Distance (m): 20 ~ 200 meters.
Display Modules
View AllInput Voltage: 3.7 to 5.3 V
Input Current : 320 mA
Driver Chip : MAX7219
Emitted color : Red
Display Dimensions : 32x32x6 (LxWxH) mm
PCB Dimensions : 50×32 (LxW) mm
Low current operation
Better, brighter and larger display than conventional LCD displays.
Current consumption : 30mA / segment
Peak current : 70mA
Number of Digits 4 digits
Driver Chip TM1637
Communication Interface I2C Bus
Control Pins 2 connections (CLK and DIO)
Supply Voltage Typically 5V DC (Check specific module for voltage range)
The operating voltage of this LCD is 4.7V-5.3V
It includes two rows where each row can produce 16-characters.
The utilization of current is 1mA with no backlight
Every character can be built with a 5×8 pixel box
Its display can work on two modes like 4-bit & 8-bit
These are obtainable in Blue & Green Backlight
Circuit Accessories
View AllZinbal EdTech Private Limited
S4, Sector 5, Pratap Nagar, Sanganer, Jaipur, Rajasthan 302033
Copyright © 2023, All Rights Reserved. | Zinbal EdTech Pvt. Ltd.