- +91 9024156475
- info@zinbal.com
Showing all 12 results
Model: ICR 18650
Voltage: 3.6V
Current: 2A (25℃)
Battery cell type: (8C)
Space for a standard 18650 batteries.
Cable length: 15cm.
Output: 3.7V
Dimensions (approx.): 76 x 20 x 20mm
Weight: 6g
high-quality plastic material
Space for two standard 18650 batteries.
Cable length: 15cm.
Output: 7.2V
Dimensions (approx.): 76 x 40 x 20mm
Weight: 12g
high-quality plastic material
1 channel relay board
Operating voltage 5V
Maximum current: 20mA
Relay contact current capacity at AC250V: 10A
Relay contact current capacity DC5V: 10A
Power indicator light
Control Indicator light
Trigger input voltage 3.3V – 5V
Two separate LEDs to indicate relay on/off
Back EMF Protection
Two LEDs to indicate when the relay is on.
Works with logic level signals from 3.3V or 5V devices
Module with diode current protection, short response time
AC control voltage: 250V at max 10A
DC control voltage: 30V at max 10A
9V output
metal jacket body
Excellent finish quality prevents leakage
Easy to install and replace
Corrosion-free connection points for long-term use
Mercury and cadmium 0%. Environmentally Friendly
Microcontroller: ATmega2560
Operating Voltage: 5V
Input Voltage : 7-12V
Digital I/O Pins: 54 (of which 15 provide PWM output)
Analog Input Pins: 16
DC Current per I/O Pin: 20 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 256 KB
SRAM: 8 KB
EEPROM: 4 KB
Clock Speed: 16 MHz
Microcontroller: ATmega328P
Digital I/O Pins: 14, with 6 PWM outputs
Analog Input Pins: 8
Operating Voltage: 5V
Clock Speed: 16MHz
USB Connection
Power Jack
Reset Button
Microcontroller: ATmega328P
Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Digital I/O Pins: 14, of which 6 can be used as PWM outputs
Analog Input Pins: 61
DC Current per I/O Pin: 20mA
DC Current for 3.3V Pin: 50mA
Flash Memory: 32KB (ATmega328P), 0.5KB used by bootloader
SRAM: 2KB (ATmega328P)
EEPROM: 1KB (ATmega328P)
Clock Speed: 16 MHz
Reset Button
Plug Type: 5.5 x 2.1mm
Pin: 3
Temperature: -30°C ~ +70°C.
Rated load: up to DC 30V / 1.0A.
Working voltage: DC 4.8-6V
Provides 3 modes to check servos and ESCs
You can adjust the knob to different speeds and check the response time in manual mode.
In neutral mode, the servo returns to the neutral point.
Automatic "window wiper" mode causes the servo to rotate through the widest possible angle like a window wiper.
Connect up to 3 servos simultaneously
Drive Type: Dual high-power H-bridge
Power Input: 4.5 to 9V
Communication Interface Voltage: 3.3V
Flash size: 4MB
Operating Temperature: -40 to 125°C
Transfer Rate: 110 to 460800Kbps
AD0: 1 channel ADC
Zinbal EdTech Private Limited
S4, Sector 5, Pratap Nagar, Sanganer, Jaipur, Rajasthan 302033
Copyright © 2023, All Rights Reserved. | Zinbal EdTech Pvt. Ltd.