- +91 9024156475
- info@zinbal.com
Showing 1–20 of 21 results
1 channel relay board
Operating voltage 5V
Maximum current: 20mA
Relay contact current capacity at AC250V: 10A
Relay contact current capacity DC5V: 10A
Power indicator light
Control Indicator light
Trigger input voltage 3.3V – 5V
Two separate LEDs to indicate relay on/off
Back EMF Protection
Two LEDs to indicate when the relay is on.
Works with logic level signals from 3.3V or 5V devices
Module with diode current protection, short response time
AC control voltage: 250V at max 10A
DC control voltage: 30V at max 10A
Plastic Parts Material ABS
Maximum Voltage(V) 300
Maximum Operating Current (A) 3 – 5
Allowed Wire Size (AWG) 29 ~ 20
Dimensions 170mmx64mm
Working voltage: DC 4.8-6V
Provides 3 modes to check servos and ESCs
You can adjust the knob to different speeds and check the response time in manual mode.
In neutral mode, the servo returns to the neutral point.
Automatic "window wiper" mode causes the servo to rotate through the widest possible angle like a window wiper.
Connect up to 3 servos simultaneously
This is a single-row 40-pin female header/pin header. You can cut it to your desired size with a wire cutter. The standard pitch for this header is 2.0mm. Technical Specs
Number of Pins: 40
Pin Spacing: 2 mm
Strip Length: 80.60 mm
Strip width: 2.49 mm
Strip Height: 6.8 mm (with contact Points)
These are 40-pin 20cm female-to-female jumper wires. A very flexible and easily detachable cable to the number of wires per your requirements. It has a female connector on each end. It also supports pin headers with a 2.54mm pitch. Technical Specs
Cable Type : Female to Female
Number of Pins: 40
Length : 200mm
The HC-05 6 Pin Wireless Serial Bluetooth Module is a Bluetooth module to be used with any microcontroller. It uses the UART protocol to simplify sending and receiving wireless data.
Operating voltage: 3.6 ~ 6V.
Input current: 50mA
Maximum Operating Range: 10m.
Operating Frequency: 2.4GHz ISM band.
Modulation: GFSK (Gaussian Frequency Shift Keying).
Operating Temperature: -20 ~ +75℃.
Input Supply Voltage: 2.5 ~ 5.5(VDC)
Transmission Distance: 45 m
Carrier Frequency: 38 kHz
Beam Angle: 45 deg
Viewing Angle: 45 deg
Output Current: 5 mA
Power Dissipation: 10 mW
This is a single-row 40-pin male header/pin header. You can cut it to your desired size with a wire cutter. The standard pitch for this header is 2.0mm. Technical Specs
Number of Pins: 40
Pin Spacing: 2 mm
Strip Length: 80.60 mm
Strip width: 2.49 mm
Strip Height: 6.8 mm (with contact Points)
These are 40-pin 20cm male-to-female jumper wires. A very flexible and easily detachable cable to the number of wires per your requirements. It has a 1-pin male connector and a 1-pin female connector on each end. It also supports pin headers with a 2.54mm pitch. Technical Specs
Cable Type : Male to Female
Number of Pins: 40
Length : 200mm
These are 40-pin 20cm male-to-male jumper wires. A very flexible and easily detachable cable to the number of wires per your requirements. It has a male connector on each end. It also supports pin headers with a 2.54mm pitch. Technical Specs
Cable Type : Male to Male
Number of Pins: 40
Length : 200mm
Plastic Parts Material ABS
Mounting Holes M2
Maximum Operating Current (A) 3 – 5
Allowed Wire Size (AWG) 29 ~ 20
Dimensions 46mmx36mm
Up to 480 Mbps data transfer rate.
USB Type: Type-A to Mini-B.
Exclusively designed for Arduino boards.
Zero PCB is a standard cause revealed circuit board (PCB) called DOT PCB. This is a thin, rigid copper plate with pre-drilled holes at standard intervals on a grid with 2.54 mm (0.1 inch) spacing among holes.
Technical Specs
Dimension: 50 × 75mm
Copper Thickness 1-4 OZ
Board Thickness 0.7-1.2mm
Min. Hole Size 0.3mm
PCB colour: Brown
Receiver Type 50 Channels
GPS L1 frequency, C/A Code
SBAS: WAAS, EGNOS, MSAS
Input Supply Voltage: 2.7 ~ 6 VDC
Main Chip: NEO-6
Navigation Update Rate 5Hz
Position Accuracy: 2Meter
Operating Temperature Range: -24 to 84 °C
Tracking Sensitivity: -161 dBm
Avg Cold Start Time: 27s
Warm Start Time: 27s
Maximum Speed: 500 M/s
Drive Type: Dual high-power H-bridge
Power Input: 4.5 to 9V
Communication Interface Voltage: 3.3V
Flash size: 4MB
Operating Temperature: -40 to 125°C
Transfer Rate: 110 to 460800Kbps
AD0: 1 channel ADC
Operating voltage: 5V.
Quiescent Current: 4mA.
Receiving frequency: 315MHz.
Receiver sensitivity: 105 dB.
Communication Distance (m): 20 ~ 200 meters.
TTL serial port for serial port, you can link directly to the micro-controller.
Power module automatically boots, homing network.
Onboard signal lights all the way.
It flashes slowly when there is a signal, it flashes quickly when there is no signal.
Operating Voltage : 3.7 ~ 4.2VDC
Peak Current : 2A
Maximum Voltage(V) 300
Maximum Operating Current (A) 3 – 5
Allowed Wire Size (AWG) 29 ~ 20
Dimensions 82mx55mm
Weight (gm) 40
This is a USB 2.0 A-B Cable for Arduino and Home Printers (1.5 meters)
This USB cable is a Type-A to Type-B.
It is designed with a 1.5 meter and features in gold plated connector.
This cable is fully compatible with the PC.
Molded strain relief and PVC over molding to ensure a lifetime of error-free
data transmissions.
Zinbal EdTech Private Limited
S4, Sector 5, Pratap Nagar, Sanganer, Jaipur, Rajasthan 302033
Copyright © 2023, All Rights Reserved. | Zinbal EdTech Pvt. Ltd.