- +91 9024156475
- info@zinbal.com
Showing 1–20 of 21 results
Shaft length: 7 mm
Motor Design: L-Shaped
Shaft Diameter: 5.5 mm
Size: 55 x 48 x 23 mm.
Operating Voltage: 3 to 12V
Current (without loading): 40-180mA
RPM: 150 rpm
Output Torque: 0.8 kg cm.
RPM: 150.
Operating Voltage: 12V DC
Gearbox: Attached Plastic (spur)Gearbox
Shaft diameter: 6mm with internal hole
Torque: 2 kg-cm
No-load current = 60 mA(Max)
Load current = 300 mA(Max).
Shaft length: 7 mm
Shaft Diameter: 5.5 mm
Size: 55 x 48 x 23 mm.
Operating Voltage: 3 to 12V.
Current (without loading): 40-180mA.
RPM: 150 rpm.
Output Torque: 0.8 kg cm.
RPM: 300.
Operating Voltage: 12V DC
Gearbox: Attached Plastic (spur)Gearbox
Shaft diameter: 6mm with internal hole
Torque: 1 kg-cm
No-load current = 60 mA(Max)
Load current = 300 mA(Max).
1 channel relay board
Operating voltage 5V
Maximum current: 20mA
Relay contact current capacity at AC250V: 10A
Relay contact current capacity DC5V: 10A
Power indicator light
Control Indicator light
Trigger input voltage 3.3V – 5V
Two separate LEDs to indicate relay on/off
Back EMF Protection
Two LEDs to indicate when the relay is on.
Works with logic level signals from 3.3V or 5V devices
Module with diode current protection, short response time
AC control voltage: 250V at max 10A
DC control voltage: 30V at max 10A
Wheel Size: 65mm x 26mm
WEIGHT: 20.00g
The geared DC motor will operate on voltages between 3-9VDC.
Plastic Yellow Rim
Robot Wheel is suitable for all BO motors
Wheel Diameter – 70 mm
Wheel Width – 20 mm
Shaft Diameter – 6 mm
Weight: 33gm
Working voltage: DC 4.8-6V
Provides 3 modes to check servos and ESCs
You can adjust the knob to different speeds and check the response time in manual mode.
In neutral mode, the servo returns to the neutral point.
Automatic "window wiper" mode causes the servo to rotate through the widest possible angle like a window wiper.
Connect up to 3 servos simultaneously
The HC-05 6 Pin Wireless Serial Bluetooth Module is a Bluetooth module to be used with any microcontroller. It uses the UART protocol to simplify sending and receiving wireless data.
Operating voltage: 3.6 ~ 6V.
Input current: 50mA
Maximum Operating Range: 10m.
Operating Frequency: 2.4GHz ISM band.
Modulation: GFSK (Gaussian Frequency Shift Keying).
Operating Temperature: -20 ~ +75℃.
Input Supply Voltage: 2.5 ~ 5.5(VDC)
Transmission Distance: 45 m
Carrier Frequency: 38 kHz
Beam Angle: 45 deg
Viewing Angle: 45 deg
Output Current: 5 mA
Power Dissipation: 10 mW
Supply Voltage: 4.5V to 36V
Output Current: 600mA per channel (continuous)
Number of Channels: 2 H-bridge channels
H-Bridge Configuration: Bidirectional control
Package Type: DIP
Supply Voltage: 5V to 35V
Output Current : 2A per channel (continuous)
Number of Channels : 2 H-bridge channels
H-Bridge Configuration : Bidirectional control
Maximum Power Dissipation : Up to 25W (Tcase = 75°C)
Maximum Frequency : 100kHz
Enable and Status Pins : Available for each channel
Operating Voltage : 3 ~ 6V
Operating Current: 130 ~ 220mA
Flow Rate : 80 ~ 120 L/H
Maximum Lift : 40 ~ 110 mm
Continuous Working Life : 500 hours
Receiver Type 50 Channels
GPS L1 frequency, C/A Code
SBAS: WAAS, EGNOS, MSAS
Input Supply Voltage: 2.7 ~ 6 VDC
Main Chip: NEO-6
Navigation Update Rate 5Hz
Position Accuracy: 2Meter
Operating Temperature Range: -24 to 84 °C
Tracking Sensitivity: -161 dBm
Avg Cold Start Time: 27s
Warm Start Time: 27s
Maximum Speed: 500 M/s
Drive Type: Dual high-power H-bridge
Power Input: 4.5 to 9V
Communication Interface Voltage: 3.3V
Flash size: 4MB
Operating Temperature: -40 to 125°C
Transfer Rate: 110 to 460800Kbps
AD0: 1 channel ADC
Operating voltage: 5V.
Quiescent Current: 4mA.
Receiving frequency: 315MHz.
Receiver sensitivity: 105 dB.
Communication Distance (m): 20 ~ 200 meters.
TTL serial port for serial port, you can link directly to the micro-controller.
Power module automatically boots, homing network.
Onboard signal lights all the way.
It flashes slowly when there is a signal, it flashes quickly when there is no signal.
Operating Voltage : 3.7 ~ 4.2VDC
Peak Current : 2A
Rated Voltage: 5V
Rated Current: 500 mA
Step Angle: 5.625°/64
Reduction ratio: 64:1
Resistance: 50Ω
In-Traction Frequency: >600 Hz
Out-Traction Frequency: >1000 Hz
In-traction Torque: 34.3mN-m
Self-positioning Torque: 34.3mN-m
Insulation Grade: A
Shaft Type: Double D-Type
Modulation: Analog
Torque:
- 4.8V: 2.20 kg-cm
- 6.0V: 2.50 kg-cm
Speed: 4.8V: 0.11 sec/60°, 6.0V: 0.10 sec/60°
Weight: 0.49 oz (14.0 g)
Gear Type: Metal
Rotation/Support: Dual Bearings
Rotational Range: 180°
Pulse Cycle: 20 ms
Pulse Width: 400-2400 µs
Zinbal EdTech Private Limited
S4, Sector 5, Pratap Nagar, Sanganer, Jaipur, Rajasthan 302033
Copyright © 2023, All Rights Reserved. | Zinbal EdTech Pvt. Ltd.