- +91 9024156475
- info@zinbal.com
Showing all 19 results
Shaft length: 7 mm
Motor Design: L-Shaped
Shaft Diameter: 5.5 mm
Size: 55 x 48 x 23 mm.
Operating Voltage: 3 to 12V
Current (without loading): 40-180mA
RPM: 150 rpm
Output Torque: 0.8 kg cm.
RPM: 150.
Operating Voltage: 12V DC
Gearbox: Attached Plastic (spur)Gearbox
Shaft diameter: 6mm with internal hole
Torque: 2 kg-cm
No-load current = 60 mA(Max)
Load current = 300 mA(Max).
Shaft length: 7 mm
Shaft Diameter: 5.5 mm
Size: 55 x 48 x 23 mm.
Operating Voltage: 3 to 12V.
Current (without loading): 40-180mA.
RPM: 150 rpm.
Output Torque: 0.8 kg cm.
RPM: 300.
Operating Voltage: 12V DC
Gearbox: Attached Plastic (spur)Gearbox
Shaft diameter: 6mm with internal hole
Torque: 1 kg-cm
No-load current = 60 mA(Max)
Load current = 300 mA(Max).
1 channel relay board
Operating voltage 5V
Maximum current: 20mA
Relay contact current capacity at AC250V: 10A
Relay contact current capacity DC5V: 10A
Power indicator light
Control Indicator light
Trigger input voltage 3.3V – 5V
Two separate LEDs to indicate relay on/off
Back EMF Protection
Two LEDs to indicate when the relay is on.
Works with logic level signals from 3.3V or 5V devices
Module with diode current protection, short response time
AC control voltage: 250V at max 10A
DC control voltage: 30V at max 10A
Microcontroller: ATmega2560
Operating Voltage: 5V
Input Voltage : 7-12V
Digital I/O Pins: 54 (of which 15 provide PWM output)
Analog Input Pins: 16
DC Current per I/O Pin: 20 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 256 KB
SRAM: 8 KB
EEPROM: 4 KB
Clock Speed: 16 MHz
Microcontroller: ATmega328P
Digital I/O Pins: 14, with 6 PWM outputs
Analog Input Pins: 8
Operating Voltage: 5V
Clock Speed: 16MHz
USB Connection
Power Jack
Reset Button
Microcontroller: ATmega328P
Operating Voltage: 5V
Input Voltage (recommended): 7-12V
Digital I/O Pins: 14, of which 6 can be used as PWM outputs
Analog Input Pins: 61
DC Current per I/O Pin: 20mA
DC Current for 3.3V Pin: 50mA
Flash Memory: 32KB (ATmega328P), 0.5KB used by bootloader
SRAM: 2KB (ATmega328P)
EEPROM: 1KB (ATmega328P)
Clock Speed: 16 MHz
Reset Button
Wheel Size: 65mm x 26mm
WEIGHT: 20.00g
The geared DC motor will operate on voltages between 3-9VDC.
Plastic Yellow Rim
Robot Wheel is suitable for all BO motors
Wheel Diameter – 70 mm
Wheel Width – 20 mm
Shaft Diameter – 6 mm
Weight: 33gm
Working voltage: DC 4.8-6V
Provides 3 modes to check servos and ESCs
You can adjust the knob to different speeds and check the response time in manual mode.
In neutral mode, the servo returns to the neutral point.
Automatic "window wiper" mode causes the servo to rotate through the widest possible angle like a window wiper.
Connect up to 3 servos simultaneously
Supply Voltage: 4.5V to 36V
Output Current: 600mA per channel (continuous)
Number of Channels: 2 H-bridge channels
H-Bridge Configuration: Bidirectional control
Package Type: DIP
Supply Voltage: 5V to 35V
Output Current : 2A per channel (continuous)
Number of Channels : 2 H-bridge channels
H-Bridge Configuration : Bidirectional control
Maximum Power Dissipation : Up to 25W (Tcase = 75°C)
Maximum Frequency : 100kHz
Enable and Status Pins : Available for each channel
Operating Voltage : 3 ~ 6V
Operating Current: 130 ~ 220mA
Flow Rate : 80 ~ 120 L/H
Maximum Lift : 40 ~ 110 mm
Continuous Working Life : 500 hours
Drive Type: Dual high-power H-bridge
Power Input: 4.5 to 9V
Communication Interface Voltage: 3.3V
Flash size: 4MB
Operating Temperature: -40 to 125°C
Transfer Rate: 110 to 460800Kbps
AD0: 1 channel ADC
Rated Voltage: 5V
Rated Current: 500 mA
Step Angle: 5.625°/64
Reduction ratio: 64:1
Resistance: 50Ω
In-Traction Frequency: >600 Hz
Out-Traction Frequency: >1000 Hz
In-traction Torque: 34.3mN-m
Self-positioning Torque: 34.3mN-m
Insulation Grade: A
Shaft Type: Double D-Type
Modulation: Analog
Torque:
- 4.8V: 2.20 kg-cm
- 6.0V: 2.50 kg-cm
Speed: 4.8V: 0.11 sec/60°, 6.0V: 0.10 sec/60°
Weight: 0.49 oz (14.0 g)
Gear Type: Metal
Rotation/Support: Dual Bearings
Rotational Range: 180°
Pulse Cycle: 20 ms
Pulse Width: 400-2400 µs
Model: SG90
Weight: 9 gm
Operating voltage: 3.0V~ 7.2V
Servo Plug: JR
Stall torque @4.8V : 1.2kg-cm
Zinbal EdTech Private Limited
S4, Sector 5, Pratap Nagar, Sanganer, Jaipur, Rajasthan 302033
Copyright © 2023, All Rights Reserved. | Zinbal EdTech Pvt. Ltd.