- +91 9024156475
- info@zinbal.com
Showing all 19 results
The operating voltage of this LCD is 4.7V-5.3V
It includes two rows where each row can produce 16-characters.
The utilization of current is 1mA with no backlight
Every character can be built with a 5×8 pixel box
Its display can work on two modes like 4-bit & 8-bit
These are obtainable in Blue & Green Backlight
Number of Digits 4 digits
Driver Chip TM1637
Communication Interface I2C Bus
Control Pins 2 connections (CLK and DIO)
Supply Voltage Typically 5V DC (Check specific module for voltage range)
1 channel relay board
Operating voltage 5V
Maximum current: 20mA
Relay contact current capacity at AC250V: 10A
Relay contact current capacity DC5V: 10A
Power indicator light
Control Indicator light
Trigger input voltage 3.3V – 5V
Two separate LEDs to indicate relay on/off
Back EMF Protection
Two LEDs to indicate when the relay is on.
Works with logic level signals from 3.3V or 5V devices
Module with diode current protection, short response time
AC control voltage: 250V at max 10A
DC control voltage: 30V at max 10A
Low current operation
Better, brighter and larger display than conventional LCD displays.
Current consumption : 30mA / segment
Peak current : 70mA
Plastic Parts Material ABS
Maximum Voltage(V) 300
Maximum Operating Current (A) 3 – 5
Allowed Wire Size (AWG) 29 ~ 20
Dimensions 170mmx64mm
Working voltage: DC 4.8-6V
Provides 3 modes to check servos and ESCs
You can adjust the knob to different speeds and check the response time in manual mode.
In neutral mode, the servo returns to the neutral point.
Automatic "window wiper" mode causes the servo to rotate through the widest possible angle like a window wiper.
Connect up to 3 servos simultaneously
This is a single-row 40-pin female header/pin header. You can cut it to your desired size with a wire cutter. The standard pitch for this header is 2.0mm. Technical Specs
Number of Pins: 40
Pin Spacing: 2 mm
Strip Length: 80.60 mm
Strip width: 2.49 mm
Strip Height: 6.8 mm (with contact Points)
These are 40-pin 20cm female-to-female jumper wires. A very flexible and easily detachable cable to the number of wires per your requirements. It has a female connector on each end. It also supports pin headers with a 2.54mm pitch. Technical Specs
Cable Type : Female to Female
Number of Pins: 40
Length : 200mm
This is a single-row 40-pin male header/pin header. You can cut it to your desired size with a wire cutter. The standard pitch for this header is 2.0mm. Technical Specs
Number of Pins: 40
Pin Spacing: 2 mm
Strip Length: 80.60 mm
Strip width: 2.49 mm
Strip Height: 6.8 mm (with contact Points)
These are 40-pin 20cm male-to-female jumper wires. A very flexible and easily detachable cable to the number of wires per your requirements. It has a 1-pin male connector and a 1-pin female connector on each end. It also supports pin headers with a 2.54mm pitch. Technical Specs
Cable Type : Male to Female
Number of Pins: 40
Length : 200mm
These are 40-pin 20cm male-to-male jumper wires. A very flexible and easily detachable cable to the number of wires per your requirements. It has a male connector on each end. It also supports pin headers with a 2.54mm pitch. Technical Specs
Cable Type : Male to Male
Number of Pins: 40
Length : 200mm
Input Voltage: 3.7 to 5.3 V
Input Current : 320 mA
Driver Chip : MAX7219
Emitted color : Red
Display Dimensions : 32x32x6 (LxWxH) mm
PCB Dimensions : 50×32 (LxW) mm
Plastic Parts Material ABS
Mounting Holes M2
Maximum Operating Current (A) 3 – 5
Allowed Wire Size (AWG) 29 ~ 20
Dimensions 46mmx36mm
Up to 480 Mbps data transfer rate.
USB Type: Type-A to Mini-B.
Exclusively designed for Arduino boards.
Zero PCB is a standard cause revealed circuit board (PCB) called DOT PCB. This is a thin, rigid copper plate with pre-drilled holes at standard intervals on a grid with 2.54 mm (0.1 inch) spacing among holes.
Technical Specs
Dimension: 50 × 75mm
Copper Thickness 1-4 OZ
Board Thickness 0.7-1.2mm
Min. Hole Size 0.3mm
PCB colour: Brown
Maximum Voltage(V) 300
Maximum Operating Current (A) 3 – 5
Allowed Wire Size (AWG) 29 ~ 20
Dimensions 82mx55mm
Weight (gm) 40
This is a USB 2.0 A-B Cable for Arduino and Home Printers (1.5 meters)
This USB cable is a Type-A to Type-B.
It is designed with a 1.5 meter and features in gold plated connector.
This cable is fully compatible with the PC.
Molded strain relief and PVC over molding to ensure a lifetime of error-free
data transmissions.
USB Type: Type-A to Type-B
Fully compatible with the PC.
Aluminum under-mold shield helps meet FCC requirements on KMI/RFI interference.
Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference
Zinbal EdTech Private Limited
S4, Sector 5, Pratap Nagar, Sanganer, Jaipur, Rajasthan 302033
Copyright © 2023, All Rights Reserved. | Zinbal EdTech Pvt. Ltd.