- +91 9024156475
- info@zinbal.com
Showing 1–20 of 44 results
1 channel relay board
Operating voltage 5V
Maximum current: 20mA
Relay contact current capacity at AC250V: 10A
Relay contact current capacity DC5V: 10A
Power indicator light
Control Indicator light
Trigger input voltage 3.3V – 5V
Two separate LEDs to indicate relay on/off
Back EMF Protection
Two LEDs to indicate when the relay is on.
Works with logic level signals from 3.3V or 5V devices
Module with diode current protection, short response time
AC control voltage: 250V at max 10A
DC control voltage: 30V at max 10A
Plastic Parts Material ABS
Maximum Voltage(V) 300
Maximum Operating Current (A) 3 – 5
Allowed Wire Size (AWG) 29 ~ 20
Dimensions 170mmx64mm
The range of operating voltage is 3 to 5 V
Output: Both Digital & Analog Signal
The sensitivity of the microphone (1kHz) is 52 to 48 dB
Operate on Low Power
Connection Interface: I2C
operating voltage 2.5 ~ 3.6 V
12 sensing inputs
Auto calibration of each sensor
Operating Voltage: 2.5V-5.5V
Startup Calibration Delay: 0.5 Sec
Current Consumption: < 7 µA
Simple, easy to use, with Auto Calibration
Power: 2.7V to 5.5V
Interface: digital TTL
High-resolution conversion of light intensity to frequency
Programmable color and full-scale output frequency
Communicates directly to microcontroller
Operating Voltage: 3.5V to 5.5V
Operating current: 0.3mA
Output: Serial data
Temperature Range: 0°C to 50°C
Humidity Range: 20% to 90%
Accuracy: ±1°C and ±1%
LM393-based design.
Sensitivity adjustable (potentiometer adjustment).
Operating voltage: 3.3V to 5V DC.
Operating current: 15mA.
Module pin 3 pins.
The output type is digital output (D0).
Working voltage: DC 4.8-6V
Provides 3 modes to check servos and ESCs
You can adjust the knob to different speeds and check the response time in manual mode.
In neutral mode, the servo returns to the neutral point.
Automatic "window wiper" mode causes the servo to rotate through the widest possible angle like a window wiper.
Connect up to 3 servos simultaneously
This is a single-row 40-pin female header/pin header. You can cut it to your desired size with a wire cutter. The standard pitch for this header is 2.0mm. Technical Specs
Number of Pins: 40
Pin Spacing: 2 mm
Strip Length: 80.60 mm
Strip width: 2.49 mm
Strip Height: 6.8 mm (with contact Points)
These are 40-pin 20cm female-to-female jumper wires. A very flexible and easily detachable cable to the number of wires per your requirements. It has a female connector on each end. It also supports pin headers with a 2.54mm pitch. Technical Specs
Cable Type : Female to Female
Number of Pins: 40
Length : 200mm
Size : 2.2inch
Operating voltage : 0-5V
Can operate on LOW voltages
Operating temperature: -45ºC to +80ºC
Flat Resistance: 25K Ω
Resistance Tolerance: ±30%
Actuation force as low as 0.2N
Sensitivity ranges up to 20N
Cost-effective
Ultra-thin
Operating temperature: -40ºC to +85ºC
None actuated Resistance: 10M Ω
Resistance Range: 100K to 1K Ohms (depending on force)
Optimal Sensing Distance: 3mm
Max. Recommended Sensing Distance: 6mm
Distance between two IR sensors: 15mm
PCB Size ( L x W ) : 126 x 26mm
Input voltage: 4 V to 12 V (+ 5 V recommended)
Output: Digital Signal
Working range: up to 20 cm away
Able to work at low current (20mA)
Directional movements are simply two potentiometers - one for each axis
Compatible with Arduino interface
The biaxial XY Joystick Module KY-023 applies ARDUINO
Dimensions: 1.57 in x 1.02 in x 1.26 in (4.0 cm x 2.6 cm x 3.2 cm)
5 Pin
This is a single-row 40-pin male header/pin header. You can cut it to your desired size with a wire cutter. The standard pitch for this header is 2.0mm. Technical Specs
Number of Pins: 40
Pin Spacing: 2 mm
Strip Length: 80.60 mm
Strip width: 2.49 mm
Strip Height: 6.8 mm (with contact Points)
These are 40-pin 20cm male-to-female jumper wires. A very flexible and easily detachable cable to the number of wires per your requirements. It has a 1-pin male connector and a 1-pin female connector on each end. It also supports pin headers with a 2.54mm pitch. Technical Specs
Cable Type : Male to Female
Number of Pins: 40
Length : 200mm
These are 40-pin 20cm male-to-male jumper wires. A very flexible and easily detachable cable to the number of wires per your requirements. It has a male connector on each end. It also supports pin headers with a 2.54mm pitch. Technical Specs
Cable Type : Male to Male
Number of Pins: 40
Length : 200mm
Zinbal EdTech Private Limited
S4, Sector 5, Pratap Nagar, Sanganer, Jaipur, Rajasthan 302033
Copyright © 2023, All Rights Reserved. | Zinbal EdTech Pvt. Ltd.